复杂环境下氧化铝储槽定向爆破拆除

在较为复杂的环境下,爆破拆除钢筋混凝土氧化铝储槽。该储槽自重大、呈圆形,内有4根立柱支撑下料漏斗。为使储槽顺利定向倒塌,通过爆破方案选择、参数确定,采取梯形切口和预处理以及安全防护和减振措施,使储槽爆破拆除获圆满成功。     

The role of microbial electrogenesis in regulating methane and nitrous oxide emissions from constructed wetland-microbial fuel cell

This study assesses a sustainable solution to greenhouse gases (GHGs) mitigation using constructed wetland-microbial fuel cells (CW-MFC). Roots of wetland plant Acorus Calamus L. are placed in biological anode to better enable anode microorganisms to obtain rhizosphere secretion for power improvement. Three selected cathode materials have a large difference in GHG emissions, and among them, carbon fiber felt (CFF) shows the lowest emissions of methane and nitrous oxide, which are 0.77 ± 0.04 mg/(m²·h) and 130.78 ± 13.08 μg/(m²·h), respectively. The CFF CW-MFC achieves the maximum power density of 2.99 W/m³. As the influent pH value is adjusted from acidic to alkaline, the GHGs emissions are reduced. The addition of Ni inhibits GHGs emission but decreases the electricity, the power density is reduced to 1.09 W/m³, and the methane and nitrous oxide emission fluxes decline to 0.20 ± 0.04 mg/(m²·h) and 15.49 ± 1.86 μg/(m²·h), respectively. Low C/N ratio reduces methane emission, while high C/N ratio effectively inhibits nitrous oxide emission. At the influent pH 8 and C/N = 5:1, the methane emission flux is approximately 10.60 ± 0.27 mg/(m²·h), and the nitrous oxide emission flux is only 10.90 ± 1.10 μg/(m²·h). Based on the above experimental results by controlling variable factors, it is proposed that CW-MFC offers an environment-friendly solution to regulate GHG emissions.     

A NEW OIL SEEPAGE IN THE OMAN MOUNTAINS AND ITS GEOLOGICAL,GEOCHEMICAL AND PETROLEUM SYSTEMS CONTEXT

A minor natural oil seepage is described from an unlikely setting in the Oman Mountains. The host rocks are fractured pelagic limestones of the lower member of the Triassic – Lower Jurassic Matbat Formation of the Hamrat Duru Group in the lower part of the allochthonous Hawasina Complex. This paper summarises Oman's established oil families and documents previously recorded oil seepages as context for describing the new seepage, its geochemistry, and possible source rock. The seep oil is different to those known from Oman's oil fields and probably derived from a poor quality, Mesozoic clastic source rock containing a mix of terrigenous and marine organic matter. The most likely source appears to be the Toarcian turbiditic upper member of the Matbat Formation, equivalent to the clastic Mafraq Formation of the Arabian Platform. The occurrence of source rocks in the allochthonous sediments of the NeoTethyan Hawasina Basin has been suspected previously, though their commercial significance remains to be established.     

Shock/expansion fan interaction with real gas effects for Earth and Mars atmospheric conditions

Numerical simulations are performed to investigate the real gas effects on shock/expansion fan interaction. Initial perfect gas simulations at low enthalpy capture the flow structures efficiently and outcomes are found to have excellent agreement with the analytical calculations. Furthermore, the simulations with the real gas solver for different enthalpies showed that the variation in enthalpy significantly changes the flow structures. It is observed that an increase in enthalpy leads to a decrease and increase in the postshock and postexpansion fan Mach numbers, respectively. Another important observation is the decrement in the peak pressure ratio with an increment in the enthalpy. These effects are noted to be more pronounced for Mars's environment due to the higher dependency of specific heat on temperature.     

Mg gas infiltration for the fabrication of MgB2 pellets using nanosized and microsized B powders

MgB₂ superconductor pellets were synthesized through Mg gas infiltration method using nanosized- and microsized B powders. There was a marked difference in the superconducting properties of the two samples, particularly in the pinning force and dominant pinning mechanism. The microstructures of the samples were observed using HR-TEM and STEM-HAADF, and the results showed that the primary reason for the difference in the superconducting properties is the distribution of the nanosized second-phase particle MgO. Additionally, a feasible reaction model for the Mg gas infiltration method was established. Compared to the Mg liquid infiltration method, the gas infiltration showed better penetrability ability with a small amount of residual Mg. This study presents a novel synthesis process to fabricate an MgB₂ pellet with superior density and superconducting properties. This method can be used in multiple applications such as superconducting bearings, compact superconductor magnets, and magnetic shielding.     

水力空化改质对重质原油沥青质及性质的影响

利用水力空化过程产生局部的高温、高压、高射流以及强大的剪切力等极端化学物理条件改质处理沙特重质原油，试验结果表明：沙特重质原油经过水力空化改质后粘度由13.61降低至7.22mm2/s，残碳由7.16%降低至6.48%，实沸点蒸馏后减压渣油降低1个百分点。进一步采用APPI FT-IR MS、XRD、FT-IR、SEM和粒度分布等技术研究了水力空化改质对沙重原油分子组成，沥青质团聚体微晶结构、沥青质胶束粒径分布、沥青质官能团、沥青质形貌等方面的影响，从分子角度阐述空化改质重油的机理。研究结果表明：水力空化改质后沙重原油分子量分布、芳烃类化合物缔合作用变小；沥青质对低DBE化合物吸附性能降低；沥青质团聚体微晶结构更加松散；沥青质胶束粒度分布降低；沥青质分子相互团聚作用力减弱。进一步考察了水力空化改质前后减压渣油延迟焦化性能，改质处理后焦炭产率降低1.85个百分点，液体收率和气体产率分别增加1.52和0.33个百分点，水力空化改质对沥青质性质、结构特点的改善能够有效的提高其加工性能。     

Understanding on the hydrogen detection of plasma sprayed tin oxide/tungsten oxide (SnO2/WO3) sensor

The plasma spray technique was well proven in producing metal oxide based gas sensors in the last two decades using different powder feedstocks. However, limited research was made to fabricate hydrogen gas sensor from tin oxide layer coated over tungsten oxide layer. This paper attempts to interpret the hydrogen gas sensing performances of plasma sprayed coating derived by depositing tin oxide layer over tungsten oxide (SnO₂/WO₃) layer. Plasma sprayed SnO₂/WO₃ sensor showed maximum response of 90% at 150 °C in contrast to stand-alone WO₃ (89% at 350 °C) and stand-alone SnO₂ (89% at 250 °C). The lower operating temperature of SnO₂/WO₃ sensor without compromising gas response was attributed to the WO₃–SnO₂ hetero-junction. SnO₂/WO₃ sensor showed selective sensing towards hydrogen with respect to carbon monoxide and methane gases. This sensor also possessed repeatable characteristics after 39 days from the initial measurement. In a nut-shell, plasma spayed SnO₂/WO₃ sensor showed stability of base resistance, repeatability after successive response and recovery cycles, selective sensing towards 500 ppm H₂ with significant magnitude of gas response of 90%, response time of 35 s and recovery time of 269 s at a temperature of 150 °C.     

Ammonia gas sensing and magnetic permeability of enhanced surface area and high porosity lanthanum substituted Co–Zn nano ferrites

This work reports magnetic permeability and ammonia gas sensing characteristics of La³⁺ substituted Co–Zn nano ferrites possessing chemical formula Co_0.7Zn_0.3La_xFe_2-2xO₄ (x = 0–0.1) synthesized by a sol-gel route. Refinement of X-ray diffraction (XRD) patterns of the ferrite powders by the Rietveld technique has revealed the creation of single-phase spinel structure. The tenancy of constituent cations at tetrahedral/octahedral sites was obtained from the refinement of XRD. The crystallite sizes calculated from the W–H method vary from 20 to 24 nm. The scanning electron microscope (SEM) profiles of the ferrite samples were analyzed for the morphological details. The energy dispersive X-ray analysis (EDAX) patterns of the samples were obtained to test the elemental purity of the ferrites within their stoichiometry. The transmission electron microscope (TEM) image of the ferrite (x = 0.1) exhibits the spherical and oval shaped particles with a mean size of 20 nm. Fourier transform infra-red (FTIR) spectra were analyzed to confirm the superseding of La³⁺ cations at octahedral sites. The Brunauer-Emmett-Teller (BET) analysis of nitrogen adsorption-desorption isotherms of the ferrites was performed to investigate the porous structure and to determine the surface area of the nanocrystalline ferrites. The oxidation states of the constituent ions were confirmed by means of X-ray photoelectron spectroscopy (XPS). The complex permeability as a function of frequency was studied to explore the effects of structural parameters on the magnetic behaviour of the ferrites. Analysis of gas sensing properties of the ferrites have proved that the Co–Zn–La ferrite with controlled La composition can be utilized as an effective ammonia gas sensing material in commercial gas sensors.     

Experimental study and numerical modeling of mixing by air injection in yield stress fluids using the OpenFOAM software

Mixing by gas injection is an operation used in industrial processes such as wastewater treatment, metallurgy, or methanization in which pressurized gas is injected into a fluid in order to reduce concentrations and temperatures gradients. This study demonstrates how the CFD toolbox OpenFOAM can be used to simulate such flows. Experimental measurements and observations have been performed on a pilot-scale reactor where pressurized air is injected in a yield stress fluid. The volume of fluid method and an adaptive mesh with refinement at the interface have been used to track the gas inclusions. The numerical model accuracy has been assessed by comparing experimental and numerical results related to the bubble's frequency, dimensions, and rising velocities as well as the fluid recirculation, yielded, and unyielded regions in the tank. The influence of injection parameters such as the injection flow rate and the fluid rheological parameters has been quantified.     

Antioxidant Activity of Piceatannol in Canola Oil

Piceatannol has shown to be a strong antioxidant in vivo, however, its ability to suppress lipid oxidation in foods has not been examined. The present study is to examine the antioxidant effect of piceatannol on heated canola oil compared with that of butylated hydroxytoluene (BHT). The oxidation of canola oil is conducted at 60, 90, 120, and 150 °C by monitoring the depletion of oxygen, the decrease in unsaturated fatty acids, and the changes of primary and secondary oxidation products. Results demonstrated that piceatannol can suppress lipid oxidation of canola oil in a dose-dependent manner with its effect being more effective than BHT. Practical Applications: Lipid oxidation is a major factor in the deterioration of food quality. Synthetic antioxidants, such as BHT and butylated hydroxyanisole, are used to inhibit oxidation in foods, but their safety has been always concerned. Piceatannol has exhibited a strong antioxidant activity to attenuate lipid oxidation and it should be further explored for use as a natural antioxidant in foods.